40’ 3 Point Toolbar
Excellent Performance for Side-Dressing
The Demco 40’ 3 point mounted fertilizer toolbar is built with high quality and features for you to get the job done. With our Saddle Tank Systems and Lil’ Thumper Ground Driven Pumps, we are no stranger to fertilizer equipment.
Our SideQuest Saddle Tank Systems are the perfect fit for our 40’ 3 point fertilizer toolbar. This setup will provide you with good capacity for side-dressing, with excellent visibility in the field, and superior maneuvering which will minimize crop damage.
- Bar uses a center linkage with two cylinders attached. One cylinder is for folding and the second is for wing “Kick Up”. This feature “kicks” the wings up 8 degrees to avoid knocking crops down when turning on headlands.
- The “Kick Up” cylinder and “Folding” cylinder are on two separate hydraulic blocks so when the tool bar is unfolded the bar will be in the “Kicked” up position. This feature prevents the coulters from crashing into the ground.
- Hydraulic down pressure to keep coulters in the ground. Down pressure can easily be adjusted without the use of tools.
- The 40' bar has built in flex that allows the inner wing to move 8 degrees above and below horizontal.
- The bar can be folded from 40' to 30' by folding the outer wings.
- Category “3” or “4” rear mount brackets may be used with “Quick Attach” three point hookup.
- Transport width - 19' 7"
- Note: Warranty void if bar is not equipped with standard coulters listed in Options or if used with center articulating tractors
Three Point Toolbar
|9413001||Three Point Toolbar|
Note: Warranty void if bar is not equipped with standard coulters listed below or if used with center articulating tractors
|9413002||20" Smooth Blade with Injector, Shield|
|9413003||20" Smooth Blade with Knife, Shield|
|9413022||20" Crucible Fluted Blade with Injector, Shield|
|9413023||20" Crucible Fluted Blade with Knife, Shield|
|9413004||20" Smooth Blade with Injector, Gen III Yetter|
|9413005||20" Smooth Blade with Knife, Gen III Yetter|
|9413026||20" Rippled Blade with Spring Tine Injector, Gen III Yetter|
|9413027||20" Rippled Blade with Knife, Gen III Yetter|
|9413006||20" Smooth Blade with Injector, Xtreme Yetter (Requires Orifice)|
|9413007||20" Smooth Blade with Knife, Xtreme Yetter|
|9413029||20" Rippled Blade with Injector, Xtreme Yetter (Requires Orifice)|
|9413030||20" Rippled Blade with Knife, Xtreme Yetter|
|9413032||20" Smooth Blade with Spring Tine Injector, 2996 Parallel Yetter|
|9413033||20" Smooth Blade with Knife, 2996 Parallel Yetter|
|9413034||20" Rippled Blade with Spring Tine Injector, 2996 Parallel Yetter|
|9413035||20" Rippled Blade with Knife, 2996 Parallel Yetter|
|9413008||Hypro Hydraulic Stainless Steel Pump (9306S-HM1C- B3U) (hoses included)|
|9413009||Hypro Hydraulic Pump (9306C-HM1C- BU) (hoses included)|
|9413010||Ace Hydraulic Stainless Steel Pump (FMC-150FS-HYD- 206) (hoses included)|
|9413011||Ace Hydraulic Pump (FMC-150-HYD- 304) (hoses included)|
Plumbing / Pump Mount / Ball Valves
|9413012||30" 15 Coulter, 3 Section|
|9413013||30" 15 Coulter, 5 Section|
|9413014||30" 17 Coulter, 3 Section|
|9413015||30" 17 Coulter, 5 Section|
|9413016||20" 23 Coulter, 3 Section|
|9413017||20" 23 Coulter, 5 Section|
|9413018||20" 25 Coulter, 3 Section|
|9413019||20" 25 Coulter, 5 Section|
|9425092||Raven® 440 Rate Controller, 3 Section, GPS Speed Sensor 1Hz|
|9425093||Raven® 450 Rate Controller, 5 Section, GPS Speed Sensor 1Hz|
|9413025||Offset Kit for 20" Rows, Shield|
|9413028||Offset Kit for 20" Rows, Yetter|
|AF20057 30' 30-40' 3 Point Toolbar||March 17, 2020||Rev. 2|